Updating simlock error 0x1

Time taken 0.78s Flashing Speed: 836,31 k Bit/S Restarting MCU... You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!

RM-348_32.001_003_000_U001fpsx, Type: Flash Image, Algo: XSR 1.5, BB5 Searching for Boot Code: Dual Line 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 5.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. Flash Chip[0, CMT]: 0x0000000000000000, Unknown, RAM Flash Chip[0, CMT]: 0x FFFF000000000000, Unknown, MMC Flash Chip[0, CMT]: 0x0400000000000000, Unknown, NOR Flash Chip[1, CMT]: 0x0000000100000000, Unknown, NOR Flash Chip[0, CMT]: 0x00EC004000000121, Samsung, ONENAND Requested Algorithm: XSR 1.5 (CMT) Searching for Boot Code: Dual Line 32Bit Flash Chip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 5.1, Algo: XSR 1.5 Initializing Turbo Cache...

Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: B2075F4B793BB9017C8C0097C783C543F2A6A303 Flashbus Write baud set to 5.0Mbits Started group flash erase Erase Area[0, CMT]: 0x0A960000-0x0F71FFFF, ONENAND Waiting 320s for erasure finish...

Time taken 19.188s Flashing Speed: 6985,24 k Bit/S Restarting MCU... You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!

SX4 Status: Not authorized (74) Started mutual authenthication with card... You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!

updating simlock error 0x1-31updating simlock error 0x1-79

Certificates OK Started group flash erase Erase Area[0, CMT]: 0x00400000-0x007FFFFF, ONENAND Waiting 320s for erasure finish...

Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: B2075F4B793BB9017C8C0097C783C543F2A6A303 Flashbus Write baud set to 5.0Mbits Sending Certificates...

Time taken 2.984s Flashing Speed: 7278,37 k Bit/S Restarting MCU...

RM-348_32.001_53.1_prd.customer.fpsx, Type: Flash Image, Algo: XSR 1.5, BB5 Searching for Boot Code: Dual Line 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 5.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. Flash Chip[0, CMT]: 0x0000000000000000, Unknown, RAM Flash Chip[0, CMT]: 0x FFFF000000000000, Unknown, MMC Flash Chip[0, CMT]: 0x0400000000000000, Unknown, NOR Flash Chip[1, CMT]: 0x0000000100000000, Unknown, NOR Flash Chip[0, CMT]: 0x00EC004000000121, Samsung, ONENAND Requested Algorithm: XSR 1.5 (CMT) Searching for Boot Code: Dual Line 32Bit Flash Chip 0x00EC0040 (Samsung), Size: 256MBytes, VPP: Not Supported RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 5.1, Algo: XSR 1.5 Initializing Turbo Cache...

Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: B2075F4B793BB9017C8C0097C783C543F2A6A303 Flashbus Write baud set to 5.0Mbits Started group flash erase Erase Area[0, CMT]: 0x09F60000-0x0A95FFFF, ONENAND Waiting 320s for erasure finish...

Leave a Reply

Your email address will not be published. Required fields are marked *

One thought on “updating simlock error 0x1”